 |
Category: Educational
» Results 1 - 20 of 24
Mini Chopper Days 8 & 9
All of LCC's characters make an appearance in this video. Beav & Hormann take their first rides on the chopper. We attach the tensioner pulley to the new throttle grip and work on attaching the rear fender.
Size: 24mb (.mp4 format)
Mini Chopper Day 10 - Part 1
We were given a steel fire door and decided to make the gas tank out of it. However, in order to do that, we had to dismantle the thing. That's pretty much all that happens. We destroy a door, and Arch hurts himself.
Size: 31mb (.mp4 format)
Mini Chopper Day 10 - Part 2
We start fabricating the coffin-style gas tank for our mini chopper.
Size: 37mb (.mp4 format)
Mini Chopper Day 11 - Part 1
We finish the initial fabrication of the coffin-style gas tank.
Size: 25mb (.mp4 format)
Mini Chopper Day 13
This time, we break down the chopper to the frame, cut new motor mount grooves, TIG weld the neck gusset, and clean the components.
Size: 23mb (.mp4 format)
Mini Chopper Day 12
After a slight miscommunication, we fabricate mounting brackets for the coffin-style gas tank.
Size: 31mb (.mp4 format)
Mini Chopper Day Seven
This time we work on the front and rear fenders. We're also using the new wide angle lens for the first time.
Size: 28mb (.mp4 format)
A Mastercard Moment
There are times when things happen that are just so funny that you have to tell others about it. As luck would have it, the camera was running when it happened.
Size: 4mb (.mp4 format)
Shop Stool
Here are the video highlights of the shop stool build from last week. We used the down tubes from a derelict Huffy bicycle that Arch found, a piece of 1/8" plate, 1 1/4" x 1/4" flat bar, 2" x 1" x 1/8" square tube, a cotter pin and key, and a few pieces...
Size: 7mb (.mp4 format)
Mini Chopper Day 11 - Part 2
We work on mounting and foaming the seat pan. The foam that we use is 1 1/4" closed cell plumbing insulation.
Size: 27mb (.mp4 format)
The Galleyware Company
TSCC interviews Galleyware's Chris Nonnenmacher at the 2005 U.S. Sailboat Show in Annapolis, MD.
Size: 13mb (.mp4 format)
Mini Chopper Day Three
In this video, we fabricate the forks and risers in order to finish the rolling chassis.
Size: 35mb (.mp4 format)
Mini Chopper Day One
This is the video of the first day of fabrication on the mini chopper frame. The audio is a little over-modulated from time to time.
Size: 40mb (.mp4 format)
Mini Chopper Day Two
In this video, we finish the mini chopper frame.
Size: 21mb (.mp4 format)
Mini Chopper Day Six
This time, we work on the engine to get maximum performance and take the chopper out for a test drive. We've been working on several side projects lately. Turns out that in order to finish the motorcycle, we needed to make some tools.
Size: 18mb (.mp4 format)
Stick Figures
It's a side project day. Arch had to take the day off, so I made some pen-holding stick figures for a local church's silent auction.
Size: 28mb (.mp4 format)
Mini Chopper Days 4 & 5
On Day 4, we weld the handlebars together and make room for the permanent axles. On Day 5, we make a seat pan, install the engine and pulleys, and ride the chopper for the first time.
Size: 36mb (.mp4 format)
Poker Expert Interview
This is really great interview with Columbo. He is the autor of pokerwannabe.blogspot.com and the One Minute Mystery. The first 20 minutes are Q&A, then they analyze five hands for tourament #5. His analysis is first rate.
Size: 58mb (.mp4 format)
The Mirror World
Take a virtual tour around Seattle using Google Earth and stop by to see some videos from our archive. Geovlogging is the process of associating a geographic location to a video blog post.
Size: 29mb (.mp4 format)
Dual Boot Tutorial
Another great tutorial about this new apple software...
Size: 12.1mb (.mp4 format)
[1]
2
|
|
Info: 
